V65t - Truck mounted sweepers | Bucher Municipal | Australia

V65t

Engineered to last,
designed to perform

V65t
Engineered to last, designed to perform

The V65t has been developed to provide longer on-station time, maximum performance, low operational costs & low impact to the environment

The V65t provides longer on-station time with the lowest environmental impact, combined with ease of use and low operational costs.
With up to 3,600mm swept width, the V65t is the sweeper of choice worldwide for both municipal and cotractor sweeping applications.

 

 

Get to know the V65t

Cost
Lower Cost of Ownership
Lower Cost of Ownership

Designed to last

V65t sweeper operates at the lowest cost, with a large 190 litre auxiliary fuel tank giving increased on-station time. In addition, maintenance costs are significantly reduced on the gearbox and fluid coupling, as no belts or high wearing components are required. The Bucher V65t provides the lowest emissions and running costs. Suction sweeping requires fewer components, resulting in less wear and tear which in turn reduces maintenance costs.

Technology
Operational Performance
Operational Performance

Designed to suit operational requirements

The V65t is designed to fit a wide range of chassis models to suit specific operational requirements, the V65t sweeper will provide the power and performance to complete the task. In-cab controls are ergonomically positioned to provide safe and easy operation whilst sweeping. The CANbus system monitors sweeper performance and provides daily checks. The 7” JVM display incorporates as standard an audible and visual raised hopper warning, fuel gauge, engine hour metre, tachometer and a water level gauge. In addition data can be downloaded via a USB stick, showing a range of information from fuel consumption to average sweeping times. Throttle control of the auxiliary engine is infinitely variable ensuring optimum operational and fuel efficiency with no performance compromised.

With a 1500 rev Eco-mode built into the V65t, fuel conservation and noise levels are enhanced. A full CANbus integrated door mounted control pad allows the operator to safely adjust all the sweep options.

​V Range Centre console

 

Performance
Productivity
Productivity

Maximising on-station time

Maximising on-station time requires a balance of having enough water capacity to minimize refills, having enough hopper capacity to cope with large volumes of leaves or debris, having a payload great enough to meet demands of a workday and being able to carry enough fuel to reduce non-productive travel.
The V65t provides the ideal balance between performance, environmental impact and low cost of ownership, with applications to suit a full range of sweeping environments, benefits that make the Bucher V65 the sweeper of choice worldwide.

Performance
Low Environmental Impact
Low Environmental Impact

Low Water usage

The V65t uses as standard yellow mist atomizing jets to reduce water usage by 20%, or red nozzle jets with higher flow are available for heavier applications. The optional Water Recirculation system can save up to 900 litres of water per day extending the on-station time and reducing the risk of dust going through the fan.

Key specifications

  • 6.5 m³ hopper capacity
  • 1554 litre water tank
  • 4mm 1.4003 Stainless steel hopper
  • Wireless discharge control
  • Trailing sweepgear
  • 4* EUnited PM10/2.5 Certifed

Key Features

Hopper
CANbus System
Safety
Operator Experience
Water Capacity
Swept Width

Designed to last in the toughest environments

The V65t hopper is manufactured from 1.4003 stainless steel, shot blasted with aluminium oxide prior to the application of a strontium based primer followed by a hard wearing top coat. In addition, all grey parts such as the sweepgear, powerpack and subframe are shot blasted and electro-magnetically powder painted in a durable two part epoxy paint finish. This ensures the sweeper continues to look as good as it performs, retaining a high residual value or longer in-service life.

Monitor sweeper performance

The CANbus system monitors sweeper performance and provides daily checks. The display incorporates as standard an audible and visual raised hopper warning, fuel gauge, engine hour meter, tachometer and a water level gauge. In addition data can be downloaded via a USB stick, showing a range of information from fuel consumption to average sweeping times.

A full CANbus integrated door mounted control pad is offered as an option, allowing the operator to safely adjust all the sweep options.

 The new V65t is equipped with a radio controlled remote pendant allowing the operator to walk completely around the sweeper without having wires to contend with.

 The operator can adjust the wide sweep brush easily to extend brush life and can check the surroundings before opening the hopper or tipping.

Designed with Safety in mind

The highly visible, self-engaging body prop provides the operator and service personnel with a safe working environment. The V65t features a wireless radio controller allowing the operator to walk completely around the sweeper. The operator can adjust the wide sweep brush easily and check surrounds before opening the rear door or tipping.

High visibility brush plates and hose sleeves make it easier for the operator to see the brush position. The V65t is also supplied with an LED sweepgear work light as standard and a wide range of additional LED and hazard warning lights are also available.

The auxiliary engine is accessed via a wide lightweight service ladder giving three-point of contact, which can be folded away when not in use. All critical controls including valves, solenoids and auxiliary equipment for pneumatic, hydraulic and water systems are contained in a purpose built locker on the right hand side of the vehicle. The ease of access to this equipment facilitates diagnostic checks and maintenance.

Additionally, the V65t is also fitted with waterproof IP67 automotive electrical connectors for enhanced reliability. V65t model has equipment storage lockers on both sides of the hopper for storage of hydrant or wanderhose extension tubes.

Designed with the operator in mind

The in-cab centre console featuring cup holders and USB charging points can be adjusted to suit the operators preference. The 7” colour JVM screen is mounted on an articulated arm allowing tilt angle and rotation to be adjusted without the need for any tools. The JVM has a wide range of settings that can be tailored to suit the operational needs.

The ergonomic door controller (offered as an extra option) can be used for all sweeping operations, brush position, pressure, speed, nozzle aperture, engine revs and water jets. A heavy duty pause button allows the operator to lift all the sweepgear until depressed again. This allows the operator to change from sweeping to transit in a quick and easy way. The V65t remembers the last sweeping settings used each time.

Up to 2254 litres

The V65t has a 1554 litre stainless steel water tank integrated in the lower portion of the hopper and an optional 700 litre additional water tank is also available. The V65t uses yellow mist atomizing jets to reduce water usage by 20%, alternatively red nozzle jets with higher flow are available for heavier applications. For increased productivity, an optional water recirculation system can save up to 900 litres of water per day extending the on-station time and with the added advantage of reducing dust emissions.

Up to 3600mm with simultaneous sweep option

The V65t offers up to 3600mm swept width with the simultaneous sweep option (for dual sweep machines only), set almost flat makes short work of light application surface cleaning.

Product options

Thumbnail

V65t with twin
engine

Twin engine options offering performance and flexibility for truck mounted sweepers
Being independent of the truck chassis, the sweeper auxillary engine powers the sweeping functions and vacuum system so both engine and chassis can be tailored to the application and customer preferences. A wide range of chassis can also be supplied with either manual, automatic or automated gearboxes providing a wide range of options to suit the operator.
The V65t has a JCB 55 kW industrial engine designed for operating in dusty environment. Providing 410 Nm of torque at 1200 rpm the Stage 5 engine is ideally suited for road sweeping operations whilst offering low fuel consumption (EU27 only).
The option of a JCB 97 kW engine is also available offering a max torque of 550 Nm at 1500 rpm for applications where higher suction power is required; for example more arduous road construction operations (EU27 only).
Outside of the EU an optional JCB 85 kW Stage 3a can be offered with a max torque of 440 Nm at 1300 rpm.
Throttle control of the auxiliary engine is infinitely variable ensuring optimum operational and fuel efficiency with no performance compromised. With a 1500 rev Eco-mode built into the V65t, fuel conservation and noise levels are enhanced.
Once set to an operating performance, the twin engine sweeper system will perform at the same level regardless of gradient and travel speed. The sweeping operation can be paused or stopped easily and sweep gear lifted to allow the driver to transit from one location to another without having to disengage a separate drive.

Read more Read less

Other truck mounted sweepers

Discover Bucher Municipal

Find out why Bucher Municipal is the perfect partner for you. 

Why Bucher Municipal

The partner you can always rely on to help you achieve more

Get to know more
Maintenance & Repair

Maintaining your vehicle in a roadworthy condition

Read more
Spare parts & accessories

Genuine parts that ensure reliability

Spare parts e-shop
Sustainability

Clear the way for a greener tomorrow 

Read more
Bucher Connect

All-inclusive digital fleet management

Get to know more

Buy our products
and services

Providing products and services
around the world.

Buy Products and Services